Biatlon sling for crossbows

Biatlon sling for crossbows

I INVENTED THIS STRAP AND THEN TESTED IT MYSELF AT THE BEGINNING OF 2016. THIS CROSSBOW STRAP IS A NOVELTY THAT ALLOWS YOU TO USE AND CARRY A CROSSBOW IN DIFFICULT TERRAIN AND HAVE BOTH HANDS FREE !!!

WHAT WAS PREVIOUSLY IMPOSSIBLE IS BEING TAKEN TO ANOTHER LEVEL.

THE CROSSBOW BACK STRAP IS MADE OF HIGH QUALITY CZECH CHROME / BLACK COWHIDE WITH A THICKNESS OF ABOUT 3.5 MM, FITTINGS OF BLACK ANODIZED DURALUMIN AND STAINLESS STEEL.

THE STRAP IS IDEAL IF YOU WANT TO CARRY YOUR CROSSBOW COMFORTABLY AND SAFELY, FOR EXAMPLE, DURING EXTREME ASCENTS OR DESCENTS, WHEN WALKING IN DEBRIS FIELDS OR OTHER DIFFICULT TERRAIN, AND HAVE IT COCKED WITH THE ARROW READY TO FIRE AT A MOMENT'S NOTICE.

YOU CAN TAKE THE COCKED CROSSBOW OFF YOUR SHOULDERS IN A FEW SECONDS - THE BOTTOM STRAP IS FINISHED WITH A RUBBER BAND, JUST LIKE IN BIATHLON RACES. YOU CAN IMMEDIATELY TAKE OFF THE CROSSBOW OR ANY OTHER WEAPON - AIM AND SHOOT! WITH THIS STRAP YOU CAN ALSO RIDE A BIKE OR CROSS-COUNTRY SKI.

THE ELASTIC ALLOWS YOU TO TAKE IT OFF/ON QUICKLY WHILE KEEPING YOUR WEAPON FIRMLY ON YOUR BACK.

ATTACHING THE STRAP TO YOUR CROSSBOW, BOW OR ANY OTHER WEAPON IS VERY EASY , THERE ARE TWO VARIANTS:

VARIANT A - A STAINLESS STEEL BOLT ABOUT 5 CM LONG WITH A DIAMETER OF 6 MM WITH METRIC THREAD IS STICKING OUT OF THE STRAP, YOU CUT A THREAD M6 IN ANY WEAPON AND THEN SCREW THE STRAP INTO IT, THEN COMES A STAINLESS STEEL WASHER AND A STAINLESS STEEL COUNTER-MAT M6 WITH A PRESS-ON SILON AGAINST LOOSENING, ALL INCLUDED IN THE STRAP.

OPTION B - FROM THE STRAP THERE IS A STAINLESS STEEL GRAFT, IN WHICH A PRECISION HOLE IS REAMED FOR A PIN INTO WHICH THE NORMAL SHOULDER STRAP IS FASTENED. THIS PIN IS ALWAYS INCLUDED WITH ALMOST EVERY GUN. THE PIN IS SIMPLY SLIPPED ONTO THE PIN AND THEN SECURED WITH A SPRING-LOADED QUICK RELEASE , THE DIAMETER OF THE COTTER WIRE IS 3MM. THE COTTER PIN IS INCLUDED IN THE ASSEMBLY. EVERYTHING IS SHOWN IN THE PICTURE.

VARIANT A OR B YOU CAN SPECIFY IN THE NOTE - IT DEPENDS ON YOU WHICH ONE YOU CHOOSE.

AT THE BOTTOM OF THE BARREL, EACH ARM IS FINISHED WITH TWO 8MM DIAMETER HOLES.

YOU WILL PASS THE BLACK RUBBER THROUGH THE TOP HOLE IN THE SLING PAD - MAKE A KNOT IN THE RUBBER AND THEN PASS IT THROUGH THE HOLE IN THE BACK OF THE STOCK ON YOUR CROSSBOW, PREFERABLY SOMEWHERE BELOW THE CHEEKPIECE. IF YOU DON'T HAVE ANY HOLES ON THE STOCK, YOU CAN EASILY DRILL THEM. FOR EXAMPLE, THE EXCALIBUR MICRO AND GRIZZLY MODELS HAVE THEM, SO YOU DON'T HAVE TO DRILL ANYTHING. THEN YOU FEED THE RUBBER BACK INTO THE BOTTOM HOLE ON THE STRAP. BY USING THE POSITION OF THE KNOT YOU ADJUST THE LENGTH OF THE RUBBER AND THUS THE PULL OF THE GUN ON YOUR BACK. ALL INGENIOUSLY SIMPLE AND RELIABLE. OF COURSE, YOU CAN DO THIS OPERATION FOR BOTH LEFT AND RIGHT.  SETTING AND FIXING IS A MATTER OF ABOUT 2 MINUTES. FOR IMMEDIATE SHOOTING, YOU DO NOT REMOVE THE HANDGUARD - IT ALWAYS REMAINS ATTACHED TO THE CROSSBOW.

MADE IN CZECH REUBLIC

Translated with DeepL.com (free version)